A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?

Router1# copy running-config flash Router1(config)# copy running-config flash Router1# copy running-config startup-config Router1(config)# c...

From what location can a router load the Cisco IOS during the boot process? (Choose two.)

RAM TFTP server NVRAM setup routine Flash memory terminal

What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?

only the Layer 2 source address only the Layer 2 destination address only the Layer 3 source address only the Layer 3 destination address th...

Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)

1 2 3 4 5 6

What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)

the last restart method the command buffer contents the amount of NVRAM and FLASH used the configuration register settings the location from...

What is the default sequence for loading the configuration file?

NVRAM, FLASH, ROM FLASH, TFTP,CONSOLE NVRAM, TFTP, CONSOLE FLASH, TFTP, ROM

The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?

straight-through rollover cross-over serial

What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)

decapsulates the Layer 3 packet by stripping off the Layer 2 frame header uses the destination MAC Address in the IP Header to look up the n...

Which two statements describe characteristics of load balancing? (Choose two.)

Load balancing occurs when a router sends the same packet to different destination networks. Load balancing occurs when a router sends the s...

Which two statements correctly describe the components of a router? (Choose two.)

RAM permanently stores the configuration file used during the boot sequence. ROM contains diagnostics executed on hardware modules. NVRAM st...

Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)

source IP address: 192.168.10.129 source IP address: BBBB.3333.5677 destination IP address: 192.168.10.33 destination IP address: 192.168.10...

Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?

The passwords are encrypted. The current configuration was saved to NVRAM. The configuration that is shown will be the one used on the next ...

The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)

Sydney(config-if)# ip address 201.100.53.2 255.255.255.0 Sydney(config-if)# no shutdown Sydney(config-if)# ip address 201.100.53.1 255.255.2...

Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)

If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0. If RouterA receives a packet that is d...

Which are functions of a router? (Choose three.)

packet switching extension of network segments segmentation of broadcast domains selection of best path based on logical addressing electio...

Which of the following is the correct flow of routines for a router startup?

load bootstrap, load IOS, apply configuration load bootstrap, apply configuration, load IOS load IOS, load bootstrap, apply configuration, c...

Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?

The subnet mask of host 2 is incorrect. Host 1 and host 2 are on different networks . The switch needs an IP address that is not configured....

If a router cannot find a valid configuration file during the startup sequence, what will occur?

The startup sequence will reset. The router will prompt the user for a response to enter setup mode. The startup sequence will halt until a...

Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)

The router will change the source and destination IP address in the packet before forwarding the frame. The router will change the frame typ...

Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)

This router only has two interfaces. The router interfaces are not operational yet. This router is configured to forward packets to remote n...